Build Resin TDS
Siraya Tech Build High Resolution Resin | Sonic Grey ＆ Smoky Black
Introduction
Key Features：
Build resin combines exceptional high resolution with ultra-low shrinkage, making it the ultimate choice for highly precise fitted models, mold-making masters, and intricate scale trains. Its easy-to-process, low-odor formula strikes the perfect balance between hardness and flexibility.
Application:
- Fitted assemblies
- High-precision models
- Functional prototypes
-
Masters for mold making
Check out Build Resin here：Siraya Tech Build - High Resolution Resin
Properties
|
Mechanical Properties |
Measure |
Method |
|
Tensile Stress at Yield |
35 |
ASTM D638 |
|
Tensile Stress at Break |
33 |
ASTM D638 |
|
Young’s Modulus |
850 |
ASTM D638 |
|
Elongation at Break |
8 |
ASTM D638 |
|
Flexural Modulus |
1450 |
ASTM D790 |
|
Other Properties |
Measure |
Method |
|
HDT at 0.455 MPa |
68 |
ASTM D648 |
|
IZOD Impact (Notched) J |
27 |
ASTM D256 |
|
Shore Hardness |
77D |
ASTM D2240 |
|
Solid Density |
1.2 |
ASTM 792 |
|
Water Absorption (24hr) |
0.75% |
ASTM D570 |
|
Liquid Properties |
Measure |
Method |
|
Viscosity at 25°C (77°F) |
110 |
ASTM D7867 |
|
Liquid Density |
1.1 |
ASTM D1475 |
Work Flow
Printing
|
Material Name |
Build - High-Detail Resin (Smoky Black / Sonic Grey) |
|
Primary Printer Compatibility |
MSLA / LCD/ DLP 3D Printers |
|
Secondary Printer Compatibility |
385nm - 405nm 3D Printers |
|
Hardware Requirement |
Access to exposure control is required |
|
Supported Slicer Software |
Chitubox, Lychee Slicer, Anycubic Photon Workshop, Blueprint Studio, Elegoo Satellite |
|
Slicer Profiles Download |
Clean
|
Cleaning Step / Category |
Instructions & Recommendations |
|
Cleaning Solvents |
• Preferred: 95% concentrated Ethanol or IPA. • Alternative: Methanol (must not contain acetone). |
|
Cleaning Time |
Submerge parts in the solvents for 2-3 minutes, using the ultrasonic cleaner. |
|
Submersion Limit |
Do not submerge parts in alcohol for more than 5 minutes. |
|
Extra Step |
For complex models, use a painter brush (or any brush made with hair) to gently remove excess resin from the printed part. |
Drying
|
Drying |
Remove alcohol by using an oven for 7-8 minutes (using a hair dryer requires 10 minutes) |
|
Note: For complex parts with cavities, repeat the clean/dry cycle multiple times. |
|
|
Quality Check |
Touch the dried surface. If it is still sticky, wash and dry the part again until smooth. |
Post Curing
|
Step / Factor |
Instructions & Recommendations |
|
Preparation |
Ensure the resin is completely cleaned off and absolutely no alcohol is left on the print before curing. |
|
UV Specifications |
Use a UV light source with a wavelength of 395-405nm. |
|
Curing Time |
Cure for approximately 3-4 minutes to reach optimal strength. Parts must be fully cured before use. |
|
Recommended Method |
Direct curing without water for moisture control. |
Download Build TDS PDF
Find our Build resin user manual
Download Siraya Tech V5 test model free
Download Build Resin print setting for your 3D printers
Start printing with Build Resin now: Siraya Tech Build - High Resolution Resin