Simple Water Washable Resin TDS
This TDS is forΒ Simple Clear/ Grey/ Smoky BlackΒ only.
1. Product Introduction
Siraya Tech Simple resin offers easy cleaning with water or 15% alcohol.Β
Its low viscosity and minimal peel force enable high-speed printing on large 16K printers. This low-odor formula prevents yellowing, while Simple Clear restores to full transparency with easier post-processing, making it an ideal choice for beginners.
Application:
- Model making
- Optical and clear design.
- Easy to DYE for DIY projects
- High-speed printing
2. Property Data
|
Mechanical Properties |
Measure |
Method |
|
Tensile Stress at Yield |
27 |
ASTM D638 |
|
Tensile Stress at Break |
25 |
ASTM D638 |
|
Youngβs Modulus |
650 |
ASTM D638 |
|
Elongation at Break |
4 |
ASTM D638 |
|
Flexural Modulus |
900 |
ASTM D790 |
|
Other Properties |
Measure |
Method |
|
HDT at 0.455 MPa |
60 |
ASTM D648 |
|
IZOD Impact (Notched) J |
18 |
ASTM D256 |
|
Shore Hardness (D) |
75 |
ASTM D2240 |
|
Solid Density |
1.2 |
ASTM 792 |
|
Water Absorption (24hr) |
0.75% |
ASTM D570 |
|
Liquid Properties |
Measure |
Method |
|
Viscosity at 25Β°C (77Β°F) |
60 |
ASTM D7867 |
|
Liquid Density |
1.1 |
ASTM D1475 |
3. Work Flow
Printing
|
Material Name |
Simple Water-Wash Resin (Clear/Grey/Smoky Black) |
|
Primary Printer Compatibility |
MSLA / LCD/ DLP 3D Printers |
|
Secondary Printer Compatibility |
385nm - 405nm 3D Printers |
|
Hardware Requirement |
Access to exposure control is required |
|
Supported Slicer Software |
Chitubox, Lychee Slicer, Anycubic Photon Workshop, Blueprint Studio, Elegoo Satellite |
|
Slicer Profiles Download |
Β
Clean
|
Cleaning Step / Category |
Instructions & Recommendations |
|
Cleaning Solvents |
β’Β Preferred: 95% concentrated Ethanol or IPA. β’ Alternative: Methanol (must not contain acetone), 15% alcohol (1 part 90% alcohol + 5 parts water), or Water |
|
Cleaning Time |
Submerge parts in the solvents several times for a total of 2-3 minutes, using the ultrasonic cleaner. |
|
Submersion Limit |
DoΒ notΒ submerge parts in alcohol for more thanΒ 30 seconds. |
|
Extra Step |
For complex models, use a painter brush (or any brush made with hair) to gently remove excess resin from the printed part. |
Β
Drying
|
Drying |
Remove alcohol by using an oven for 7-8 minutes (using a hair dryer requires 10 minutes) |
|
Note: For complex parts with cavities, repeat the clean/dry cycle multiple times. |
|
|
Quality Check |
Touch the dried surface. If it is still sticky, wash and dry the part again until smooth. |
Β
Post Curing
|
Step / Factor |
Instructions & Recommendations |
|
Preparation |
Ensure the resin is completely cleaned off and absolutely no alcohol is left on the print before curing. |
|
UV Specifications |
Use a UV light source with a wavelength ofΒ 395-405nm. |
|
Curing Time |
Cure for approximatelyΒ 3-4 minutesΒ to reach optimal strength. Parts must be fully cured before use. |
|
Recommended Method |
Direct curingΒ withoutΒ water for moisture control. |
4. Additional Information
Download Simple V1Β in PDF Version.
Come and View Simple V1 User Guide
Read our Simple Blog hereΒ