Tenacious Lava TDS
Product Introduction
- Higher Impact β 50% stronger than standard resins for durable, functional parts.
- Wear Resistant β Advanced wear resistance with 73D Shore hardness for gears, joints, and mechanical assemblies.
- Large-format printer optimistic β Strong layer adhesion and minimal peel forces.
- High Precision β Sharp details, smooth finish, and deep black pigmentation.
- Versatile Engineering Applications β Prototypes, load-bearing parts, and casings, ect.
Property Data
| Mechanical Properties | Data | Method |
| Tensile Stress at Yield (Mpa) | 45 | ASTM D638 |
| Tensile Stress at Break (MPa) | 46 | ASTM D638 |
| Youngβs Modulus (MPa) | 1800 | ASTM D638 |
| Elongation at Break(%) | 75 | ASTM D638 |
| Flexural Modulus (Mpa) | 1600 | ASTM D790 |
| HDT at 0.455 MPa | 55 | ASTM D648 |
| IZOD Impact (Notched) J/m | 65 | ASTM D256 |
| Shore Hardness (D) | 73 | ASTM D2240 |
Β
| Other Properties | Data | Method |
| Solid Density g/cm3 | 1.2 | ASTM 792 |
| Liquid Density g/mL | 1.1 | ASTM D1475 |
| Water Absorption (24hr) | 2% | ASTM D570 |
| Viscosity CPS @ 25Β°C (77Β°F) | 1600 | ASTM D7867 |
Β
| Product Specifications | Detail |
| Name | Tenacious Lava |
| Color | Lava Black |
| SKU | ST0049 |
| Net weight (KG) | 1 |
| Capacity (ml) | 909 |
| Package Dimensions | 22*10*10 cm |
Β
Preparing for Printing
| Shake | 2-3 minutes |
| After shake | Settle for 10-15 minutes to dissipate bubbles |
| Build Platform Preparation | Lightly sand to improve adhesion |
| Print Temperature | β₯ 25Β°C (77Β°F) |
| Heat Resin | Pre-warm the bottle in warm (not hot) water for 10-15 minutes. |
Β
*Note:
- Consider using a space heater to warm the printing area if printing is in a cooler environment.
Printing Profile
| Printer | Download Link |
| Anycubic | Setting Profile |
| Creality | |
| Elegoo | |
| Phrozen | |
| More... |
Β
Profile Import Steps
Β
Printing Process
| Step | Key points |
| 1 | Pour the resin into the vat carefully to minimize bubble formation. |
| 2 | If bubbles form, use a silicone spatula or similar tool to gently stir the resin and pop the bubbles. |
| 3 | Settle for 5-10 minutes before starting the print. |
| 4 | Monitor the first few layers closely to ensure proper adhesion to the build platform. |
Β
*Note:Β
Some printers may have issues with the build platform pressing down fully for the first layer:
- Sensor Alerts (Saturn 3/4 Ultra & others newer printers) β You can bypass the warning and proceed with printing.
- Fix for printing the first layer not sticky β Add a thin layer of resin first. After printing the first layer, add more resin while the build platform is down.
Cleaning
Tenacious Lava Black has higher viscosity, thorough cleaning is crucial:
| Steps | Key Point |
| 1 | Let the part drain thoroughly over the vat for at least 10 minutes after finish printing |
| 2 | Prepare 90% or higher concentrated Ethanol or IPA (Isopropyl Alcohol) |
| 3 | Use the ultrasonic cleaner to clean for 10 minutes |
| 4 | Use compressed air or a hair dryer on a cool setting to dry the part thoroughly after cleaning |
| 5 | Check the dried surface by touch - if it feels sticky, clean and dry again |
Β
Post-Curing
| Steps | Key Point |
| 1 | Ensure the part is completely clean and dry before post-curing. |
| 2 | Use a 395-405nm UV light source for curing |
| 3 | Cure for approximately 15-20 minutes, rotating the part every 5 minutes for even exposure |
| 4 | Submerging the part in water can increase efficiency |
Β